MIG welding machines advices: how to become a better welder and how to select the top welding equipment. First, practice handling the gun without actually welding. Rest its barrel in one hand, and support that hand on the table. The other hand operates the gun’s trigger. Stand in a comfortable position and move the gun steadily over the work surface. Adjust your posture and gun movement so that they feel natural. Attach the work lead to the workpiece, and hold the gun so the wire meets the weld surface at about a 30-degree angle. Touch the wire very lightly to the surface, squeeze the trigger, and gently pull the gun toward you to make your first test weld. The wire should melt off into the weld puddle at an even rate and make a steady crackling noise as you go. Adjust the welder settings if needed.

Look for ways to create more efficiencies in the welding process. This includes examining such things as wire diameter, wire feed speed, voltage, travel speed, gas type, transfer mode, etc. For instance, if the shop is currently welding with a short arc process and a 75/25 blend of shielding gas, it may be more effective to switch to a different gas and a spray mode of transfer. Or, a change in process may be warranted based on the condition of the part. If there is oxide on the part, it may be easier to change to a process that will overcome contamination problems rather than try to clean each part before welding. Your welding supplier should be up to date on the latest technology and be able to advise you on new processes, machinery and consumables that can optimize welding at the shop. In some cases, it may be better to double bevel a joint to prepare it for welding rather than single bevel it. It is recommended to double bevel any material that is more than 3/4″ in thickness. Just this simple change in procedure can save quite a bit in weld metal. On a 3/4″ thick piece, a double bevel will use 1.45 lbs. per foot of weld metal while a single bevel will use 1.95 lbs. per foot.

Some tips on welding equipment, MIG and TIG welders, plasma cutters. TIG welding is similar to to a MIG welder as it uses an electric arc in the same was as MIG welding does but differs in a few ways. Instead of a continuous spool of consumable wire, a TIG welder uses long tungsten welding rods that are manually slowly fed into the weld puddle to join the metal. TIG welding requires gas, usually argon, to protect and cool the weld puddle from external contamination. TIG welding is more suited to welding thinner materials such as stainless steel and aluminium as you can get the power down lower to reduce the risk of blow through and can even weld two dissimilar metals. Suitable for tricky welds such as S curves but TIG welders are still capable of welding heavier materials depending on the machine. TIG welding takes more practice that MIG welding as the process is much more manual with controlling the torch, welding rod and gas by hand (and foot for the gas) but once mastered will produce the highest quality welds making it the better choice where perfect, precise welds are required but due to the manual process is the least productive.

Flat-Position Welding Increases Welding Speed : It’s common knowledge that welding in a horizontal position will be the easiest and fastest way to weld. A flat position is not as taxing to maintain and the welding puddle will stay in place. Take some time to evaluate each project before beginning in order to make sure the majority of welds can be completed in this position. If a job calls for vertical welding, see this article about vertical welding. Core Wire Feeder Increases TIG Welding Speed: For professional welders hoping to speed up TIG welding, a core wire feeder will add filler metal through an automated process. Watch this video on how it works. This enables welders to work with both hands and to maintain a constant flow of wire into the welding puddle. Ed Craig at the Frabricator writes about the wire feeder process first developed in Europe, saying it is “suitable for all-position welding on materials of any thickness, the process addresses traditional GTAW limitations and can enhance both manual and automated TIG weld quality and productivity.” Find more details at MIG welder.

Extend your Tungsten Electrode out Far enough but not too: Too short of a tungsten stickout from the cup will not let you hold a close enough arc length and will not let you see the tip of your electrode. You need to be able to see the tip of the electrode without getting a kink in your neck in order to keep your arc length right. Some textbooks are just plain wack when they only recommend extending your electrode one tungsten diameter past the end of the TIG cup. Holding too long an arc will not pinpoint the heat well enough and will let your rod ball up and blob into the weld.. but we already covered that didn’t we? I remember a consulting gig once where the welder at the aluminum body truck repair shop could not get the aluminum socket weld to puddle. The only thing wrong was that the electrode was recessed back in the cup. Once I extended it out about 3/8″, Everything was fine. ( I also talked them into getting some helium argon mix.)