MIG welder and welding tricks

MIG welders and a few welding guides? We have plenty posts on this topic, you can use the search box of this post doesn’t answer your questions.

Gasless welding, which is also called “Gasless” or “No-Gas” welding, is the main convenience of contemporary MIG welders. That means they can make welds either with or without gas. It is possible thanks to the use of a special tubular wire filled with a flux and metal powder called a flux-cored wire. In a nutshell, when a flux-cored wire is used, its components generate a shielding gas under a high temperature that is essential for a high-quality joint. The thermal overload protection is also a useful feature that will switch the unit off automatically if the temperature reaches a certain level. Surely, a MIG welder is not something you will carry every minute. Yet, if a machine is lightweight and fitted with wheels, using it will be much more pleasurable. Finally, pay attention to the kit each tool comes with. Some models include a welding shield, coil, attachment for flux-cored welding, hammer, or brush. So, take these features into account when buying a welder.

How to pick a welder tips: Stepped voltage or synergic: Synergic MIG’s have the edge when you’re welding stainless & aluminium as they are pre-programmed, easy to set up & portable. They also provide a better weld characteristic and so give cleaner weld bead with less/no spatter. Inverters: Considerably smaller and lighter and so ideal for site work. All inverters are stepless and so have infinite control. Also cheaper to run power wise. Budget: How much welding are you going to undertake? Gear your purchasing decision around the jobs you will be working on the most. Polarity changeover; A lot of welders at the light industrial end will to be able weld with gasless flux cored MIG wire. Is the switchover easy on the machine you’re considering. Availability of spares & after sales service: Ask where the machine is actually made. Even the more recognised brands largely outsource their production, which can lead to quality and after sales issues with lack of continuity of supply for spares.

One of the “cardinal sins” that almost every shop commits is over-welding. This means that if the drawing calls for a 1/4″ fillet weld, most shops will put down a 5/16″ weld. The reasons? Either they don’t have a fillet gauge and are not exactly sure of the size of the weld they are producing or they put in some extra to “cover” themselves and make sure there is enough weld metal in place. But, over-welding leads to tremendous consumable waste. Let’s look again at our example. For a 1/4″ fillet weld, the typical operator will use .129 lbs. per foot of weld metal. The 5/16″ weld requires .201 lbs. per foot of weld metal – a 56 percent increase in weld volume compared to what is really needed. Plus, you must take into account the additional labor necessary to put down a larger weld. Not only is the company paying for extra, wasted consumable material, a weld with more weld metal is more likely to have warpage and distortion because of the added heat input. It is recommended that every operator be given a fillet gauge to accurately produce the weld specified – and nothing more. In addition, changes in wire diameter may be used to eliminate over-welding.

A few tips on welding equipment, MIG and TIG welders, plasma cutters. Welders with a higher power output can work with thicker metals, but higher voltage welders will require special power supply set ups—either generators or appropriate power outlets. A welder with lower voltage in the 100’s will not be able to handle heavy duty jobs, but it can be plugged in and operated from any outlet. Any welder with power over 200 cannot run off a typical power outlet and will naturally cost more to run. In addition, welders will either run an alternating current (AC) that reverses itself at regular intervals or a direct current (DC) that flows in one direction and does not reverse itself. DC offers a steady rate of energy that leads to hotter temperatures and deeper weld penetration. AC welders usually cost less than DC welders, but the available electrodes are far more limited for AC. In fact, DC welders are more costly but remain popular because their higher power offers a wider selection of electrodes and a number of working advantages such as: simple arc striking, better penetration, and improved control. Welders who expect to work on a wide variety of projects may want to consider an AC/DC combination welder. Find extra info on MIG Welders Online Store.

USA market choice: LONGEVITY Inc is a company that has been around since only 2001. Like LOTOS Technology, it still produces a fine enough quality welder that it has earned its spot on this list. Besides the gas cylinder, this welder comes with everything you need to get started and is simple to set up. With all this, along with its solid performance, this machine is marked at a fair price of under $400. Though it is manufactured in China, the LONGEVITY Migweld is still a quality welder. It is most well-adapted to light use. Compared to Miller and Hobart’s machines, the price is somewhat better without sacrificing much quality. It welds from 24 gauge to ¼ inches of steel. Flux core is available for this welder. The LONGEVITY can run at ten different voltage settings. As an added bonus, it has thermal overload protection like the LOTOS welder.

If you’re a beginner welder but don’t mind splashing the cash for a top of the range welder, then try the Millermatic 141. Miller have really pushed the boundaries of usability with this welder and it features an auto-set feature for an easy set up, and infinite voltage and wire speed control. All you have to do is select the thickness of the metal you’re welding and you’re ready to start welding straight away. If you open up the machine you can tell that all the parts are great quality and really durable as well. There are more powerful welders on the market for the price, but there’s nothing better for welding up to 3/16 inch steel. See the full review here.